各位大俠，我是菜鳥初學者，請問zemax可不可以做卡塞格林望遠鏡到單模光纖的耦合效率分析，望遠鏡和光纖之間還要加透鏡的吧，哪里可以體現耦合效率呢？謝謝了！

一起學習

樓主： [Pdm1]":(  
我曾經做過這種望遠系統到光纖的耦合（從概念設計到裝調測試）。 請把你的問題再講詳細些：如望遠系統的視場，焦距，相對口徑，工作波段，光纖參數芯徑和數值孔徑。 'wAOY  
JqO#W1h~R|  
MANG2004

望遠鏡的實際焦距是3m,已經加了透鏡將焦距縮短到了1m左右，利用光纖的口徑代替光闌限制望遠鏡的視場角，望遠鏡視場角大概為0.1mrad，口徑為250mm,工作波段在532nm,光纖數值孔徑為0.1，半徑2微米。應該從望遠鏡出來的光要經過透鏡之類的才能耦合進單模光纖吧，這個透鏡要怎么設計啊，另外zemax也是初學，單模光纖也不太會弄，謝謝指教！

using Calcualtion > Fiber Coupling Efficiency or Geometric Image Analysis or Physical Optics Propagation 'jeGERMr'  
{W}.z  
there are three option depending on your system set up and the actual modelling you wish to perform

thanks a lot!

設計過300mmRC耦合，多種單光路和多光路的光纖耦合，可以聯系yaoyaogr@126.com

卡塞格林望遠鏡的口徑250MM嗎 v%=G~kF}[  

hopebox:using Calcualtion > Fiber Coupling Efficiency or Geometric Image Analysis or Physical Optics Propagation
there are three option depending on your system set up and the actual modelling you wish to perform  (2010-06-25 20:04)  H.hF`n  

xD,BlDV  
請教：光源為準平行光  而接收光纖為10微米0.15的單模光纖在pop如何設置呢

hgdjoe:請教：光源為準平行光  而接收光纖為10微米0.15的單模光纖在pop如何設置呢 (2015-04-22 11:02)  ?`bi8 Ck  

7g8}]\i+  
Apologies for late reply as I have been away for a while. The tab "Beam Definition" has a top hat which can be used as collimated beam and the receiving fiber end can be defined under the tab Fiber Data. If you have a single mode you can pick up a Beam Type to closely match your fiber mode and then define the other physical parameter accordingly.