亚洲日本欧美综合在线一 ,亚洲精品国产第一综合99久久免费,国产精品va无码免费

老司机午夜精品_国产精品高清免费在线_99热点高清无码中文字幕_在线观看国产成人AV天堂_中文字幕国产91

calice	2014-03-24 17:14
Not enough intersections allocated to finish ray trace 在zemax非序列模式下改變截止折射率經常會出現Not enough intersections allocated to finish ray trace，請問各位大大這是什么原因造成的是因為我設計的結構讓光線無法追跡么？ aw~h03R_Z 5X>~39(r [attachment=54877] Gf:dN_e6.

calice	2014-03-24 17:25
求大神幫我看看~提醒一下~

hopebox

2014-03-25 20:31

Under General > Non-Sequential tab, you will be able to set the maximum ray intersections per ray. If a ray encounters a surface of an object it counts as 1 intersection and if you are tracing "split rays" and also have "use polarization" then you could reach the maximum you set under this tab.Increasing this number would help to solve but you dont want to set it too high as it will use a lot of memory and trace the ray section that only carry small negligible amount of energy. Alternatively, you can also change the minimum energy threshold for non-sequential ray tracing so that the ray tracing will terminate at this energy threshold. Again watch out the minimum energy detectable. Hope this helps!!

calice	2014-03-28 14:38
Thank you for your help!

vivi2009wu

2014-04-01 16:55

hopebox:Under General > Non-Sequential tab, you will be able to set the maximum ray intersections per ray. If a ray encounters a surface of an object it counts as 1 intersection and if you are tracing "split rays" and also have "use polarization" .. (2014-03-25 20:31) g1"ZpD

i found that it does'nt work,if i choose the way you told .if i maxmum the core of fiber ,then the pronlem can be fixed ,but i dont know why ,can you tell me ?

calice

2014-04-10 09:54

vivi2009wu:i found that it does'nt work,if i choose the way you told .if i maxmum the core of fiber ,then the pronlem can be fixed ,but i dont know why ,can you tell me ? (2014-04-01 16:55) ./Ek+p*96H

你可以參考一下這里http://zemax.com/support/knowledgebase/what-does-not-enough-segments-allocated-to-trace-a 不知道能不能幫上你。我之前做的出現這個現象是因為發生了全反射，而我設置成無限次全反射，所以發生全反射時報錯，應該設置成全反射光能夠從平板中出去，而不是無限次全反射

hopebox	2014-05-29 19:18
vivi2009wu:i found that it does'nt work,if i choose the way you told .if i maxmum the core of fiber ,then the pronlem can be fixed ,but i dont know why ,can you tell me ? (2014-04-01 16:55) 0LL0\ly] 2 A!*8w Sorry I haven't check the forum for some time. If you still have problems you may send a file to explain what you have been doing.

olivezh

2014-06-17 20:19

calice:你可以參考一下這里http://zemax.com/support/knowledgebase/what-does-not-enough-segments-allocated-to-trace-a 不知道能不能幫上你。我之前做的出現這個現象是因為發生了全反射，而我設置成無限次全反射，所以發生全反射時報錯，應該設置成全反射光能夠從平板中 .. (2014-04-10 09:54) *m<[ sS

感謝。讀了這個才真正了解光線分解面的作用。

olivezh	2014-06-17 20:21
原來是光線在遇到分界面的時候，會分解成多束光，從而導致一個光線在傳播的過程中最終會被分解成為多個光線樹，使得計算量幾何上升，導致仿真報錯。

forlightt	2015-06-07 22:04
the maximums are not increased to a sufficient level. z[_Y,I 我的也出現過，然后設置maximum intersections per ray為4000，Maximum Segments Per Ray為10000，這個可能跟電腦配置內存大小有關系，然后我的就不再提示了

shuner	2022-02-17 11:05
節點數量不足，解決方法是Under General > Non-Sequential tab, you will be able to set the maximum ray intersections per ray.

老司机午夜精品_国产精品高清免费在线_99热点高清无码中文字幕_在线观看国产成人AV天堂_中文字幕国产91

Not enough intersections allocated to finish ray trace